Robocopy Fun

[SMosher]

Robocopy Syntax
ROBOCOPY source destination [file [file]…] [options]
where source is Source Directory (drive:\path or \\server\share\path), destination is Destination Directory (drive:\path or \\server\share\path) and file is File(s) to copy where names or wildcards can be specified and default is “*.*” (all files).
Robocopy Options and Switches
Copy options :
/S :: copy Subdirectories, but not empty ones.
/E :: copy subdirectories, including Empty ones.
/LEV:n :: only copy the top n LEVels of the source directory tree.
/Z :: copy files in restartable mode.
/B :: copy files in Backup mode.
/ZB :: use restartable mode; if access denied use Backup mode.
/EFSRAW :: copy all encrypted files in EFS RAW mode.
/COPY:copyflag[s] :: what to COPY for files (default is /COPY:DAT).
(copyflags : D=Data, A=Attributes, T=Timestamps).
(S=Security=NTFS ACLs, O=Owner info, U=aUditing info).
/DCOPY:T :: COPY Directory Timestamps.
/SEC :: copy files with SECurity (equivalent to /COPY:DATS).
/COPYALL :: COPY ALL file info (equivalent to /COPY:DATSOU).
/NOCOPY :: COPY NO file info (useful with /PURGE).
/SECFIX :: FIX file SECurity on all files, even skipped files.
/TIMFIX :: FIX file TIMes on all files, even skipped files.
/PURGE :: delete dest files/dirs that no longer exist in source.
/MIR :: MIRror a directory tree (equivalent to /E plus /PURGE).
/MOV :: MOVe files (delete from source after copying).
/MOVE :: MOVE files AND dirs (delete from source after copying).
/A+:[RASHCNET] :: add the given Attributes to copied files.
/A-:[RASHCNET] :: remove the given Attributes from copied files.
/CREATE :: CREATE directory tree and zero-length files only.
/FAT :: create destination files using 8.3 FAT file names only.
/256 :: turn off very long path (> 256 characters) support.
/MON:n :: MONitor source; run again when more than n changes seen.
/MOT:m :: MOnitor source; run again in m minutes Time, if changed.
/RH:hhmm-hhmm :: Run Hours – times when new copies may be started.
/PF :: check run hours on a Per File (not per pass) basis.
/IPG:n :: Inter-Packet Gap (ms), to free bandwidth on slow lines.
File Selection Options :
/A :: copy only files with the Archive attribute set.
/M :: copy only files with the Archive attribute and reset it.
/IA:[RASHCNETO] :: Include only files with any of the given Attributes set.
/XA:[RASHCNETO] :: eXclude files with any of the given Attributes set.
/XF file [file]… :: eXclude Files matching given names/paths/wildcards.
/XD dirs [dirs]… :: eXclude Directories matching given names/paths.
/XC :: eXclude Changed files.
/XN :: eXclude Newer files.
/XO :: eXclude Older files.
/XX :: eXclude eXtra files and directories.
/XL :: eXclude Lonely files and directories.
/IS :: Include Same files.
/IT :: Include Tweaked files.
/MAX:n :: MAXimum file size – exclude files bigger than n bytes.
/MIN:n :: MINimum file size – exclude files smaller than n bytes.
/MAXAGE:n :: MAXimum file AGE – exclude files older than n days/date.
/MINAGE:n :: MINimum file AGE – exclude files newer than n days/date.
/MAXLAD:n :: MAXimum Last Access Date – exclude files unused since n.
/MINLAD:n :: MINimum Last Access Date – exclude files used since n.
(If n < 1900 then n = n days, else n = YYYYMMDD date).
/XJ :: eXclude Junction points. (normally included by default).
/FFT :: assume FAT File Times (2-second granularity).
/DST :: compensate for one-hour DST time differences.
/XJD :: eXclude Junction points for Directories.
/XJF :: eXclude Junction points for Files.
Retry Options :
/R:n :: number of Retries on failed copies: default 1 million.
/W:n :: Wait time between retries: default is 30 seconds.
/REG :: Save /R:n and /W:n in the Registry as default settings.
/TBD :: wait for sharenames To Be Defined (retry error 67).
Logging Options :
/L :: List only – don’t copy, timestamp or delete any files.
/X :: report all eXtra files, not just those selected.
/V :: produce Verbose output, showing skipped files.
/TS :: include source file Time Stamps in the output.
/FP :: include Full Pathname of files in the output.
/BYTES :: Print sizes as bytes.
/NS :: No Size – don’t log file sizes.
/NC :: No Class – don’t log file classes.
/NFL :: No File List – don’t log file names.
/NDL :: No Directory List – don’t log directory names.
/NP :: No Progress – don’t display % copied.
/ETA :: show Estimated Time of Arrival of copied files.
/LOG:file :: output status to LOG file (overwrite existing log).
/LOG+:file :: output status to LOG file (append to existing log).
/UNILOG:file :: output status to LOG file as UNICODE (overwrite existing log).
/UNILOG+:file :: output status to LOG file as UNICODE (append to existing log).
/TEE :: output to console window, as well as the log file.
/NJH :: No Job Header.
/NJS :: No Job Summary.
/UNICODE :: output status as UNICODE.
Job Options :
/JOB:jobname :: take parameters from the named JOB file.
/SAVE:jobname :: SAVE parameters to the named job file
/QUIT :: QUIT after processing command line (to view parameters).
/NOSD :: NO Source Directory is specified.
/NODD :: NO Destination Directory is specified.
/IF :: Include the following Files.
Robocopy Examples
To use Robocopy is simple, just like how you would use Copy and Xcopy commands. For example, to copy entire folder of C:\Users to C:\UserBackup, simply type:
Robocopy C:\Users C:\UserBackup

[zhuul]

good stuff there.

[bruno]

[MoshMom]

wth does all that mean

[KrzySRT]

Again i say, HUH? LOL

[zhuul]

heh... its a list of command line options for a utility to copy files between directories/computers (over a network)/filesystems using multi-threading and a bunch of other fun features.. its a network/system administrator tool that makes life ALOT easier for alot of painful processes..

its like the old DOS copy/xcopy command but on steroids with a serious attitude problem.. hehe

heh not sure i cleared that up at all.. lol

[J12_300]

Originally Posted by SMosher

/BYTES :: Print sizes as bytes.

Thanks Man!!!